How Long For Hiv Test Results

July 2010

Today there quite a lot of news: The beads
are back, scoring board, etc. But also new are: how the micro GlueDots their world at the moment only in Baschtuegge get are only 3mm in diameter and thus even smaller than the Mini, or the bead spacers to which their People often ask, have the Deep Edge Border Punch the punching deep into it, the Chocolate Box of Coredinations and and and
Here you can watch all look at in peace and order of course! Here are the new

Wheelchair Controller Schematics

flower 3D

I had promised you a small workshop. Here he is now. As 1st
We punch out three flowers.

At the 1st
Flower cleanse her in the middle only to small sections, ideally with the cutter. (See arrow) at the 2nd
You cut off a flower petal. WARNING: This one petal you need too! At the 3rd
Flower you cut off two petals. This we need not waste more =

continues: at the 1st We take only the flower petals in shape, preferably with a pencil. Whether inside or outside is up to you. This is now ready to use and you can put aside first.

Now we take the 2nd Flower petals in the other 4 are tuned. Now we glue (I do with Glossy from Ranger, because you can simultaneously work on), the two outermost petals each other, so that we only have three. These petals as happened in the first, with the pencil into shape. Here they can definitely turn only to the outside.

The 3rd We proceed in the same flower. The two outermost petals stick together, so you can still see two of them. And also bend back into shape.
And finally you take this even one single petal, roll it so together (like a bag). (A pencil can be good to take help) then glued the edges together ma.

And now we're almost done. For now we just need to put everything together. This, too, I've had a glossy from Ranger.
Apply in the middle of a flower Bißle a glossy and the flower with the 3 flowers so deep as possible and so push stick. Now looks back out the tip, which can be cut easily.

Now you take the flower with two petals and does the same. And, finally, the last part (the single flower) and glue that can still pure.

Well, theoretically you're ready. The flowers still so ready turn in the form, where necessary.
I still hold the whole flower is sprayed with Memories Mists.

And then my obligatory bling bling stones stuck in the middle.

Hope it made some for fun and maybe then I can see one or the other flower in my forum! Häbets guet!

The workshop used products (click only and you end up in the shop):
Creatables punching templates
Glossy Ranger
adhesive stones from Kaisercraft
Memories Mists of Superior

The Creatables There are practically sold out. If, however, already ordered again.

Artistas Mexicanas Follando Amateurs

Creatables

Yes believe it or not! The blog is updated once again! But after all the trouble last year with the shop software just lacked a bit of motivation for many things.

But we forget that, the shop does so again and "almost" everything is fine again.

And so I present you here today a new product. In any case, new in Baschtuegge.

Creatables are punching and stamping Embossing is compatible with your device are: Big Shot, Epic 6 see Cuttlebug

etc. So they made:


Unwrapped they see like this:


is stamped as you are you're used to. Construction is as if punched her or Spellbinders Quickutz.


course, comes the punch template or cardstock and then the cutting board. But for better view, I took the photos Sun

by cranks and .... well, then came the first "excited." How do I get the CS (Card Stock) from the template? scratch with the cutter, with the "Güfeli" sting? Or? And each time?



Since I had the thought flash! Wife has kept for years, finally these replacement foam rubber from Quickutz. Ev. can the use yes at some point you? This has finally just now!

I have all my Creatables punching templates provided with it. WARNING: will imitate Wers: Please, only at the cutting stencils. In the Embossing you shall not, of course, but the CS will be here very easily from the back to express!

You know how yet, right? Foam stick on it, by boosting the cracks so beautiful and finished ready for use.



The punching is now to be in the way! And the result looks like this (I know that Brad does not fit at all * shame *)



And? Do not they look pretty? :-)

And now I will show you short or emboss it. From the usual in two steps.
first punch. CS can be in the form of emboss and then boost again.



And finally: Do you remember, at the very beginning of the review, the 2nd Picture? With the template (the same way as here above the yellow flower) I made this beauty!



How to do that, I tell you, but not today. I do some other time.

I should now just enter the template in the shop. Otherwise you can not order yes! Have fun making flowers. And again until gli!

Edit: Meanwhile the templates online, order here: punching templates